NOTE: The actual Daqarta SB16 index allows you to move through it
by hitting the first letter of any entry. We apologize for
this "dumbed-down" Web substitue: You may scroll through it
as usual, select a letter from the following line, or simply use your
browser's "Find" function to search this page.
AC Coupling, Input
AC Coupling, Output
Address Parameter A:
Address Parameter, Mixer A:M
Address, PnP Determination
AGC, Microphone
AGC Action Threshold Table
Anti-Alias Input Filtering, Automatic
Artifacts, DAC Output Modulation
Artifacts, OPL3 Output Modulation
Attenuation, DAC Output
Attenuation, OPL3 Output
Automatic Gain Control (AGC)
AUTOEXEC.BAT, CTCM PnP Configuration Manager
AUTOEXEC.BAT, SET BLASTER Line
Bits, ADC (8/16)
Bits, DAC Display
Bits Preset Parameter B:, ADC and DAC
BLASTER Environment String
Buffer (Queue) Length and Q: Parameter
Burst Mode, Output
Calibration, Input
Capacitor, Output Coupling
CD Input Preset C:
CD Input Source Select
Channel (Input) Parameter C:
Clear DMA / IRQ settings on Quit
Compatibility
Configuration Parameters
Control, Thumbwheel
CTCM Configuration Manager, PnP
CTPNP.CFG File
DAC Bits Control via B:Dn Parameter
DAC Bits Display
DAC Output Level Controls
Data Polarity
Delay, Output
DMA Parameter D: (8-bit)
DMA Parameter H: (16-bit)
DSP Version
Duplex Mode and B: Parameter
Duration, Output
DWCFGMG.SYS PnP Configuration Manager
eXclude Bad Sample Rates, Parameter X:
F: Parameter (Help File Omit)
Fall, Output
Filter, Automatic Input Anti-Alias
Frequency, Output
Frequency Response, Input
Frequency Response, Measuring Input
Frequency Response, DAC Output
Frequency Response, OPL3 Output
Full Duplex Mode and B: Parameter
Gain Calibration Parameter G:
Gain, Microphone
Gain Boost Parameter, OPL3 Output (CT417x only)
Gap Mode, Output
Help File Parameter F:
High DMA Parameter H: (16-bit)
Impedance, Input
Input Controls
Input Source
Invert Data Polarity
IRQ Parameter I:
Keep DMA / IRQ settings on Quit
Lag, Burst/Gap Onset with CT417x Models
Level, DAC Output
Level, OPL3 Output
Line Input Preset C:
Line Input Source Select
Line vs Speaker Output Levels
Low Frequency Response
LPT Printer Port I/O Parameter L:
Masking Experiments
Master Outputs
Menus, Synthesizer Channel
Mic Gain
Mic Input Preset C:
Mic Input Source Select
Mic Polarity Inversion
Mixer Address Parameter A:M
Modulation Artifacts, DAC Output
Modulation Artifacts, OPL3 Output
N: Parameter to iNvert Data Polarity
Noise Output
Norm / Swap OPL3 Outputs Switch
OPL3 Synthesizer Chip
Output Controls, Main
Output Gain Parameter, OPL3 (CT417x only)
Output Level, DAC
Output Level, OPL3
Output Loading Requirement
Output Mode, OPL3 (Off, On, Burst, Gap)
Output Switching, OPL3
Outputs, OPL3 Master
Outputs, Monitoring
Overload Limits
Overload Limits, Measuring
Overload Threshold Table
Parameters, Configuration
PnP Address Determination
Polarity, Data Input and Output
Range Preset Parameter R:
Range (Sensitivity)
Response, Input Frequency
Revision History
Rise, Output
Sample Rate Calibration (Advanced Users)
SBCONFIG.EXE Sets BLASTER String
Sensitivity (Range)
SET BLASTER Line
Signal Generation, Main Output Controls
Speaker vs Line Output Levels
Synthesizer Channel Menus
Synthesizer Chip, OPL3
Source, Input
Step Response and Low Frequency Response
Stimulus Source Control
Stimulus Source Preset Parameter S:
Swap OPL3 Outputs
Switching, OPL3 Output
Thumbwheel Control
Trademarks
ViBRA / WavEffects, 16-bit Full Duplex
ViBRA / WavEffects, H: Parameter Required
ViBRA / WavEffects, PnP Parameter Determination
Windows PnP Configuration
Xclude Bad Sample Rates, Parameter X:
|